AMU/IP Telefoni Haderslev Kaserne/SIP Setup/Voice VLAN - Revision history

Rael: /* Konfiguration af Management IP */

2013-09-17T13:56:35Z

‎Konfiguration af Management IP

Rael: /* Konfiguration af Management IP */

2013-05-15T07:17:10Z

‎Konfiguration af Management IP

Rael: /* Konfiguration af Management IP */

2013-05-15T07:16:56Z

‎Konfiguration af Management IP

Rael: /* Konfiguration af Access Port */

2013-05-15T07:13:53Z

‎Konfiguration af Access Port

Rael: /* Konfigurere Voice port */

2013-05-15T05:36:21Z

‎Konfigurere Voice port

Rael: /* Konfigurere access port */

2013-05-15T05:34:00Z

‎Konfigurere access port

Rael: Created page with "=Oprettelse af VLAN= Før et vlan kan bruges på en switch skal den oprettes først. VLAN 1 findes i forvejen og behøver derfor ikke at blive oprettet. Switch>..."

2013-05-14T10:42:06Z

Created page with "=Oprettelse af VLAN= Før et vlan kan bruges på en switch skal den oprettes først. VLAN 1 findes i forvejen og behøver derfor ikke at blive oprettet. <source lang=cli> Switch>..."

New page

=Oprettelse af VLAN=
Før et vlan kan bruges på en switch skal den oprettes først. VLAN 1 findes i forvejen og behøver derfor ikke at blive oprettet.
<source lang=cli>
Switch><input>en</input>
Password:
Switch#<input>configure terminal</input>
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#<input>vlan 200</input>
Switch(config-vlan)#<input>name Voice-VLAN</input>
Switch(config-vlan)#<input>exit</input>
Switch(config)#<input>end</input>
Switch#<input>show vlan brief</input>

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gi0/1, Gi0/2
<notice>200 Voice-VLAN active Fa0/1</notice>
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
Switch#
</source>
=Konfigurere access port=
Her konfigureres porten med Access VLAN 1 og VLAN 200 Voice.
<source lang=cli>
Switch#<input>configure terminal</input>
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#<input>interface fastethernet 0/1</input>
Switch(config-if)#<input>switchport mode access</input>
Switch(config-if)#<input>switchport access vlan 1</input>
Switch(config-if)#<input>switchport voice vlan 200</input>
Switch(config-if)#<input>end</input>
Switch#<input>show interface fastethernet 0/1 switchport</input>
Name: Fa0/1
Switchport: Enabled
Administrative Mode: <notice>static access</notice>
Operational Mode: <notice>static access</notice>
Administrative Trunking Encapsulation: negotiate
Operational Trunking Encapsulation: native
Negotiation of Trunking: Off
Access Mode VLAN: <notice>1 (default)</notice>
Trunking Native Mode VLAN: <notice>1 (default)</notice>
Administrative Native VLAN tagging: enabled
Voice VLAN: <notice>200 (Voice-VLAN)</notice>
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL

Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
Switch#
</source>

{{Source cli}}

@@ Line 82: / Line 82: @@
 </source>
 =Konfiguration af Management IP=
-Giv jeres Switch en IP addresse på 192.168.146.0/24 nettet, med ip .11 for gruppe 1, .12 for gruppe 2 osv.
+Giv jeres Switch en IP addresse på 192.168.139.0/24 nettet, med ip .11 for gruppe 1, .12 for gruppe 2 osv.
 <source lang=cli>
 interface Vlan1
-  ip address 192.168.146.11 255.255.255.0
+  ip address 192.168.139.11 255.255.255.0
+!
-ip default-gateway 192.168.146.1
+ip default-gateway 192.168.139.1
 ip name-server 172.16.4.66
 </source><br/><br/>

@@ Line 89: / Line 89: @@
 ip default-gateway 192.168.146.1
 ip name-server 172.16.4.66
-</source>
+</source><br/><br/>
 '''Kan du nu pinge Switchen fra din computer?'''<br/><br/>
 '''Kan du telnette til den?'''<br/><br/>
 *Konfigurer nu telnet adgang til switchen, ligesom vi lærte i sidste uge.
 {{Source cli}}

@@ Line 70: / Line 70: @@
 Switch#
 </source>
+=Konfiguration af Access Port=
+Porten hvor IPPBX'en er forbundet skal være statisk konfigureret til access port med access i VLAN 200.
 {{Source cli}}

@@ Line 28: / Line 28: @@
 Switch#
 </source>
-=Konfigurere access port=
+=Konfigurere Voice port=
 Her konfigureres porten med Access VLAN 1 og VLAN 200 Voice.
 <source lang=cli>