BO CCNA Course/coursematerials/Basic Routing Setup - Revision history

Rael: /* Setup */

2012-05-22T22:24:34Z

‎Setup

Rael: /* Tasks */

2012-05-22T22:23:48Z

‎Tasks

Rael: /* Tasks */

2012-05-22T22:23:08Z

‎Tasks

Rael: /* Tasks */

2012-05-22T22:22:29Z

‎Tasks

Rael: /* Setup */

2012-05-22T22:21:24Z

‎Setup

Rael: Created page with "=Setup= Place and connect the following equipment in Packet Tracer {| |Network |} '''This setup does not use the same host IP addres..."

2012-05-22T22:20:53Z

Created page with "=Setup= Place and connect the following equipment in Packet Tracer {| |800px|left|thumb|Network |} '''This setup does not use the same host IP addres..."

New page

=Setup=
Place and connect the following equipment in Packet Tracer
{|
|[[Image:ScreenShot1242.jpg|800px|left|thumb|Network]]
|}
'''This setup does not use the same host IP addresses as in the slide.'''

=Tasks=

#Create Labels indicating the different networks

#Document the IP addresses assigned to the devices using Labels
#Do a basic Router configuration
##Configure hostname
##Configure an enable password
##Configure a VTY password
##Configure a Console password
##Enable password encryption
##Set a loggin banner
#Configure IP addresses
##The Lowest IP address should be assigned to the Router on each LAN segment
##The DCE Router should use the lowest IP address on each Serial line

##The DTE Router should use the highest IP address on each Serial line
Are all the end devices able to ping their Default Gateway? 
Are all the Routers able to ping their neighbours? 
Are all the end devices able to ping the other end devices? 
#Configure static routing - part 1
##Configure static routing on all the Router for the 192.168.1.0/24 & 192.168.2.0/24 network
Are all the end devices able to ping the other end devices? 

#Configure static routing - part 2
##Configure complete static routing on all the router to all the networks

Are all the end devices able to ping the other end devices? 
#Delete the static routes on the routers and replace them with summary routes for the 172.16 & the 192.168 networks

@@ Line 18: / Line 18: @@
 ##Enable password encryption
 ##Set a loggin banner
-Use the show commands you know to verify Layer1+2 connectivity?<br /><br />
+'''Use the show commands you know to verify Layer1+2 connectivity?'''<br /><br />
 #Configure IP addresses
 ##The Lowest IP address should be assigned to the Router on each LAN segment
@@ Line 24: / Line 24: @@
 ##The DTE Router should use the highest IP address on each Serial line
-Are all the end devices able to ping their Default Gateway?<br /><br />
+'''Are all the end devices able to ping their Default Gateway?'''<br /><br />
-Are all the Routers able to ping their neighbours?<br /><br />
+'''Are all the Routers able to ping their neighbours?'''<br /><br />
-Are all the end devices able to ping the other end devices?<br /><br />
+'''Are all the end devices able to ping the other end devices?'''<br /><br />
 #Configure static routing - part 1
 ##Configure static routing on all the Router for the 192.168.1.0/24 & 192.168.2.0/24 network
-Are all the end devices able to ping the other end devices?<br /><br />
+'''Are all the end devices able to ping the other end devices?'''<br /><br />
 #Configure static routing - part 2
 ##Configure complete static routing on all the router to all the networks
-Are all the end devices able to ping the other end devices?<br /><br />
+'''Are all the end devices able to ping the other end devices?'''<br /><br />
 #Delete the static routes on the routers and replace them with summary routes for the 172.16 & the 192.168 networks

@@ Line 1: / Line 1: @@
 =Setup=
-Place and connect the following equipment in Packet Tracer
+Connect the following equipment in Packet Tracer
 {|
 |[[Image:ScreenShot1242.jpg|800px|left|thumb|Network]]

@@ Line 4: / Line 4: @@
 |[[Image:ScreenShot1242.jpg|800px|left|thumb|Network]]
 |}
-'''This setup does not use the same host IP addresses as in the slide.'''
+'''This setup does not use the same host IP addresses as in the slides!!'''
 =Tasks=