BO CCNA Course/coursematerials/RIP Router Setup - Revision history

Rael: /* Tasks */

2012-05-30T08:31:08Z

‎Tasks

Rael: /* Tasks */

2012-05-30T06:12:14Z

‎Tasks

Rael: /* Tasks */

2012-05-30T06:11:59Z

‎Tasks

Rael: /* Tasks */

2012-05-29T07:50:49Z

‎Tasks

Rael: added Category:CCNA using HotCat

2012-05-28T20:15:40Z

added Category:CCNA using HotCat

Rael: added Category:Cisco using HotCat

2012-05-28T20:15:31Z

added Category:Cisco using HotCat

Rael: /* Tasks */

2012-05-28T20:14:58Z

‎Tasks

Rael: /* Tasks */

2012-05-28T20:14:36Z

‎Tasks

Rael: /* Tasks */

2012-05-28T20:10:58Z

‎Tasks

Rael: Created page with "=Setup= Connect the following equipment in Packet Tracer {| |Network Setup |} =Tasks= #Create Labels indicating the different netw..."

2012-05-28T19:22:06Z

Created page with "=Setup= Connect the following equipment in Packet Tracer {| |800px|left|thumb|Network Setup |} =Tasks= #Create Labels indicating the different netw..."

New page

=Setup=
Connect the following equipment in Packet Tracer
{|
|[[Image:ScreenShot1244.jpg|800px|left|thumb|Network Setup]]
|}

=Tasks=

#Create Labels indicating the different networks

#Document the IP addresses assigned to the devices using Labels
#Do a basic Router configuration
##Configure hostname
##Configure an enable password
##Configure a VTY password
##Configure a Console password
##Enable password encryption
##Set a loggin banner
 
'''Use the show commands you know to verify Layer1+2 connectivity?''' 
#Configure IP addresses
##The Lowest IP address should be assigned to the Router on each LAN segment
##The DCE Router should use the lowest IP address on each Serial line
##The DTE Router should use the highest IP address on each Serial line
 
'''Are all the end devices able to ping their Default Gateway?''' 
'''Are all the Routers able to ping their neighbours?''' 
'''Are all the end devices able to ping the other end devices?''' 
#Configure static routing - part 1
##Configure static routing on all the Router for the 192.168.1.0/24 & 192.168.2.0/24 network
 
'''Are all the end devices able to ping the other end devices?''' 
#Configure static routing - part 2
##Configure complete static routing on all the router to all the networks
 
'''Are all the end devices able to ping the other end devices?''' 
#Delete the static routes on the routers and replace them with summary routes for the 172.16 & the 192.168 networks

@@ Line 52: / Line 52: @@
 '''Do a debug - Is RIP sending updates on the Loopback interfaces?'''<br /><br />
 #Disable updates on the Loopback interfaces
 [[Category:Cisco]]
 [[Category:CCNA]]

@@ Line 50: / Line 50: @@
 ##Add all the Loobpack interfaces to RIP
 <br/>
-'''Do a debug - Are RIP sending updates on the Loopback interfaces?'''<br /><br />
+'''Do a debug - Is RIP sending updates on the Loopback interfaces?'''<br /><br />
 #Disable updates on the Loopback interfaces
 [[Category:Cisco]]
 [[Category:CCNA]]

@@ Line 8: / Line 8: @@
 #Create Labels indicating the different networks
 #Document the IP addresses assigned to the devices using Labels
 #Do a basic Router configuration
@@ Line 33: / Line 32: @@
 ##Disable debuging
 <br/>
 '''What is the network address R2 propagetes to R3?'''<br /><br />
 '''Do the routers support receiving RIPv2 packets?'''<br /><br />
@@ Line 44: / Line 42: @@
 '''Why does R2 still propagate the classfull 172.30.0.0/16 network to R3?'''<br /><br />
 #Configure the routers to disable auto summerization at the boundary router
+<br/>
 [[Category:Cisco]]
 [[Category:CCNA]]

@@ Line 23: / Line 23: @@
 ##The DCE Router should use the lowest IP address on each Serial line
 ##The DTE Router should use the second IP address on each Serial line
 <br/>
 '''Are all the end devices able to ping their Default Gateway?'''<br /><br />

← Older revision		Revision as of 20:15, 28 May 2012
Line 45:		Line 45:

	[[Category:Cisco]]		[[Category:Cisco]]
		+	[[Category:CCNA]]

← Older revision		Revision as of 20:15, 28 May 2012
Line 43:		Line 43:
	'''Why does R2 still propagate the classfull 172.30.0.0/16 network to R3?'''<br /><br />		'''Why does R2 still propagate the classfull 172.30.0.0/16 network to R3?'''<br /><br />
	#Configure the routers to disable auto summerization at the boundary router		#Configure the routers to disable auto summerization at the boundary router
		+
		+	[[Category:Cisco]]

@@ Line 27: / Line 27: @@
 '''Are all the Routers able to ping their neighbours?'''<br /><br />
 #Configure RIPv1 routing
 ##Enable '''debug ip rip''' on the routers as you enable RIP
 ##Configure the '''network''' statement on all the connected networks. Remember: only use the classfull network

@@ Line 22: / Line 22: @@
 ##The Lowest IP address should be assigned to the Router on each LAN segment
 ##The DCE Router should use the lowest IP address on each Serial line
-##The DTE Router should use the highest IP address on each Serial line
+##The DTE Router should use the second IP address on each Serial line
 <br/>
 '''Are all the end devices able to ping their Default Gateway?'''<br /><br />
 '''Are all the Routers able to ping their neighbours?'''<br /><br />
-'''Are all the end devices able to ping the other end devices?'''<br /><br />
+#Configure RIPv1 routing
-#Configure static routing - part 1
-##Configure static routing on all the Router for the 192.168.1.0/24 & 192.168.2.0/24 network
+##Enable '''debug ip rip''' on the routers as you enable RIP
 <br/>
 '''Are all the end devices able to ping the other end devices?'''<br /><br />
-#Configure static routing - part 2
+#Configure RIPv2 Routing
-##Configure complete static routing on all the router to all the networks
 <br/>
 '''Are all the end devices able to ping the other end devices?'''<br /><br />
 #Delete the static routes on the routers and replace them with summary routes for the 172.16 & the 192.168 networks