Configure AUX to Console Relay - Revision history

Rael: /* Components Used */

2012-03-08T07:10:53Z

‎Components Used

Heth: /* Configuration */

2012-03-07T10:39:16Z

‎Configuration

Heth: /* Link */

2011-11-13T07:17:06Z

‎Link

Rael: /* Configuration */

2011-11-06T17:38:32Z

‎Configuration

Rael: Created page with "=Prerequisites= ==Components Used== RJ45-RJ45 Rollover Cable 1841 With AUX port SRX240 with Console port *Putty =Setup= The 1841 router..."

2011-09-19T12:25:29Z

Created page with "=Prerequisites= ==Components Used== 400px|right|thumb|RJ45-RJ45 Rollover Cable *1841 With AUX port *SRX240 with Console port *Putty =Setup= The 1841 router..."

New page

=Prerequisites=
==Components Used==
[[Image:IMAG0168.jpg|400px|right|thumb|RJ45-RJ45 Rollover Cable]]
*1841 With AUX port
*SRX240 with Console port
*Putty
=Setup=
The 1841 router is connected to the network and have an IP address. The AUX port on the router is connected to the console port of the SRX240 with a blue Cisco RJ45-RJ45 Rollover cable.
==Configuration==
<source lang=cli>
Router><input>enable</input>
Router#<input>configure terminal</input>
Router(config)#<input>line aux 0</input>
Router(config-line)#<input>password cisco</input>
Router(config-line)#<input>login</input>
Router(config-line)#<input>transport input all</input>
</source>
The telnet port on the router is 2000+line number. We find the line number with:
<source lang=cli>
Router#<input>show line</input>
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 0 CTY - - - - - 2 0 0/0 -
* <notice>1</notice> 1 AUX 9600/9600 - - - - - 2 0 0/0 -
* 194 194 VTY - - - - - 4 0 0/0 -
</source>
Now test it by telnetting to an ip address on the router and use port 2001
=Link=
*http://www.cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a0080094bbc.shtml
{{Source cli}}

← Older revision		Revision as of 07:17, 13 November 2011
Line 30:		Line 30:
	*http://www.cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a0080094bbc.shtml		*http://www.cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a0080094bbc.shtml
	{{Source cli}}		{{Source cli}}
		+	[[Category:Cisco]][[Category:IOS]]

@@ Line 4: / Line 4: @@
 *1841 With AUX port
 *SRX240 with Console port
 *Putty
 =Setup=
 The 1841 router is connected to the network and have an IP address. The AUX port on the router is connected to the console port of the SRX240 with a blue Cisco RJ45-RJ45 Rollover cable.

@@ Line 25: / Line 25: @@
 *   194  194 VTY              -    -      -    -    -     4      0    0/0      -
 </source>
-Now test it by telnetting to an ip address on the router and use port 2001
+Now test it by telnetting to an ip address on the router and use port 2001. To exit press <CTRL><SHIFT>6 then X
 =Link=