Etherchannel misconfig guard error - Revision history

Rael at 21:16, 14 December 2015

2015-12-14T21:16:15Z

Rael at 21:13, 14 December 2015

2015-12-14T21:13:52Z

Rael at 21:12, 14 December 2015

2015-12-14T21:12:08Z

Rael: Created page with " A2(config-if-range)#do show run Building configuration... Current configuration : 1633 bytes ! ! Last configuration change at 07:28:13 UTC Wed Mar 30 2011 ! NV..."

2015-12-14T21:11:33Z

Created page with "<source lang=cli> A2(config-if-range)#do show run Building configuration... Current configuration : 1633 bytes ! ! Last configuration change at 07:28:13 UTC Wed Mar 30 2011 ! NV..."

New page

<source lang=cli>
A2(config-if-range)#do show run
Building configuration...

Current configuration : 1633 bytes
!
! Last configuration change at 07:28:13 UTC Wed Mar 30 2011
! NVRAM config last updated at 01:45:47 UTC Wed Mar 30 2011
!
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname A2
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
system mtu routing 1500
!
!
!
no ip domain-lookup
ip domain-name CCNP.NET
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
no spanning-tree etherchannel guard misconfig
spanning-tree extend system-id
port-channel load-balance src-dst-ip
!
!
!
!
vlan internal allocation policy ascending
!
!
!
!
!
!
!
!
!
!
!
interface Port-channel1
!
interface FastEthernet0/1
switchport trunk native vlan 666
switchport mode trunk
!
interface FastEthernet0/2
switchport trunk native vlan 666
switchport mode trunk
!
interface FastEthernet0/3
shutdown
!
interface FastEthernet0/4

A2(config-if-range)#end
A2#show span
Mar 30 07:30:35.765: %SYS-5-CONFIG_I: Configured from console by console
A2#show span sum
A2#show span summary
Switch is in pvst mode
Root bridge for: none
EtherChannel misconfig guard is disabled
Extended system ID is enabled
Portfast Default is disabled
PortFast BPDU Guard Default is disabled
Portfast BPDU Filter Default is disabled
Loopguard Default is disabled
UplinkFast is disabled
BackboneFast is disabled
Configured Pathcost method used is short

Name Blocking Listening Learning Forwarding STP Active
---------------------- -------- --------- -------- ---------- ----------
Total 0 0 0 0 0
A2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
A2(config)#int ra fa 0/5 - 6
A2(config-if-range)#shut
A2(config-if-range)#no shut
Mar 30 07:31:59.231: %LINK-5-CHANGED: Interface FastEthernet0/5, changed state to administratively down
Mar 30 07:31:59.231: %LINK-5-CHANGED: Interface FastEthernet0/6, changed state to administratively down
A2(config-if-range)#no shut
A2(config-if-range)#
Mar 30 07:32:02.142: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Fa0/5, putting Fa0/5 in err-disable state
Mar 30 07:32:02.142: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Fa0/6, putting Fa0/6 in err-disable state
A2(config-if-range)#
Mar 30 07:32:02.486: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to down
Mar 30 07:32:02.495: %LINK-3-UPDOWN: Interface FastEthernet0/6, changed state to down
A2(config-if-range)#
</source>
{source_cli}

@@ Line 106: / Line 106: @@
 Mar 30 07:32:02.486: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to down
 Mar 30 07:32:02.495: %LINK-3-UPDOWN: Interface FastEthernet0/6, changed state to down
-A2(config-if-range)#
+A2(config-if-range)#end
 </source>
 {{source cli}}

@@ Line 1: / Line 1: @@
 <source lang=cli>
-A2(config-if-range)#do show run
+A2(config-if-range)#<input>do show run</input>
 Building configuration...
@@ Line 38: / Line 38: @@
+!
 spanning-tree mode pvst
-no spanning-tree etherchannel guard misconfig
+<notice>no spanning-tree etherchannel guard misconfig</notice>
 spanning-tree extend system-id
 port-channel load-balance src-dst-ip
@@ Line 72: / Line 72: @@
 interface FastEthernet0/4
-A2(config-if-range)#end
+A2(config-if-range)#<input>end</input>
-A2#show span
+A2#<input>show span</input>
 Mar 30 07:30:35.765: %SYS-5-CONFIG_I: Configured from console by console
-A2#show span sum
+A2#<input>show span sum</input>
-A2#show span summary
+A2#<input>show span summary</input>
 Switch is in pvst mode
 Root bridge for: none
-EtherChannel misconfig guard is disabled
+<notice>EtherChannel misconfig guard is disabled</notice>
 Extended system ID           is enabled
 Portfast Default             is disabled
@@ Line 92: / Line 92: @@
 ---------------------- -------- --------- -------- ---------- ----------
 Total                        0         0        0          0          0
-A2#conf t
+A2#<input>conf t</input>
 Enter configuration commands, one per line.  End with CNTL/Z.
-A2(config)#int ra fa 0/5 - 6
+A2(config)#<input>int ra fa 0/5 - 6</input>
-A2(config-if-range)#shut
+A2(config-if-range)#<input>shut</input>
-A2(config-if-range)#no shut
+A2(config-if-range)#<input>no shut</input>
 Mar 30 07:31:59.231: %LINK-5-CHANGED: Interface FastEthernet0/5, changed state to administratively down
 Mar 30 07:31:59.231: %LINK-5-CHANGED: Interface FastEthernet0/6, changed state to administratively down
-A2(config-if-range)#no shut
+A2(config-if-range)#<input>no shut</input>
 A2(config-if-range)#
-Mar 30 07:32:02.142: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Fa0/5, putting Fa0/5 in err-disable state
+<notice>Mar 30 07:32:02.142: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Fa0/5, putting Fa0/5 in err-disable state
-Mar 30 07:32:02.142: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Fa0/6, putting Fa0/6 in err-disable state
+Mar 30 07:32:02.142: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected on Fa0/6, putting Fa0/6 in err-disable state</notice>
 A2(config-if-range)#
 Mar 30 07:32:02.486: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to down