Opgave CCDP - Datacenter design - Revision history

I.P.Freely: /* Aggregation */

2009-08-13T07:36:30Z

‎Aggregation

I.P.Freely: /* Uddrag fra konfigurationer */

2009-08-12T08:58:12Z

‎Uddrag fra konfigurationer

Fatman at 08:15, 12 August 2009

2009-08-12T08:15:35Z

I.P.Freely: /* Uddrag fra konfigurationer */

2009-08-11T14:45:38Z

‎Uddrag fra konfigurationer

I.P.Freely: /* Løsning */

2009-08-11T14:45:23Z

‎Løsning

I.P.Freely: /* Default-gateway */

2009-08-11T14:45:11Z

‎Default-gateway

I.P.Freely: /* IP-scheme (Datacenter = 10.128.0.0/10) */

2009-08-11T14:44:49Z

‎IP-scheme (Datacenter = 10.128.0.0/10)

I.P.Freely: /* Point-to-point */

2009-08-11T14:44:13Z

‎Point-to-point

I.P.Freely: /* Point-to-point */

2009-08-11T14:43:19Z

‎Point-to-point

I.P.Freely: /* Point-to-point */

2009-08-11T14:42:28Z

‎Point-to-point

@@ Line 88: / Line 88: @@
 På hver aggregation-switch er der behov for følgende moduler:
 *2 stk. 48 ports switchmoduler
 *Intrusion detection (IDS)
 *Network analysis

@@ Line 150: / Line 150: @@
 Fordel for globale ACL og i edge (side 90 nederst)
 <br>
@@ Line 156: / Line 158: @@
 ==Etherchannel==
 ===Lag 3===
 DCcore1# configure terminal
 DCcore1(config)#interface port-channel 1
 DCcore1(config-if)# ip address 10.191.255.1 255.255.255.252
 DCcore1(config-if)# switchport trunk encap dot1q
 DCcore1(config-if)# switchport mode trunk
 DCcore1(config-if)# exit
 DCcore1(config)# interface range gigabitethernet 0/1 - 2
 DCcore1(config-if-range)# channel-group group 1 mode desirable
 DCcore1(config-if-range)# no shutdown
 DCcore1(config-if-range)# end
+</pre>
 ===Lag 2===
 DCagg1# configure terminal
 DCagg1(config)# interface range fastethernet 0/1 - 2
 DCagg1(config-if)# channel-group group 1 mode desirable
 DCagg1(config-if)# exit
 DCagg1(config)#interface port-channel 1
 DCagg1(config-if)# switchport mode trunk
 DCagg1(config-if)# exit
+</pre>
 ===Load balance===
 DCcore1(config)# port-channel load-balance {src-mac | dst-mac | src-dst-mac | src-ip | dst-ip |src-dst-ip}
+</pre>
@@ Line 203: / Line 193: @@
 ==HSRP==
 Eksempel med VLAN 10 og 20. DCagg1 er den foretrukken default-gateway for VLAN 10 og DCagg2 er den foretrukken default-gateway for VLAN 20.
+<pre>
 DCagg1# configure terminal
 DCagg1(config)#  interface Vlan 10
 DCagg1(config-if)# description WLC
 DCagg1(config-if)# ip address 10.130.10.1 255.255.255.0
 DCagg1(config-if)# standby 10 ip 10.130.10.254
 DCagg1(config-if)# standby 10 preempt
 DCagg1(config-if)# standby 10 track GigabitEthernet <slot/port to DCcore1>
 DCagg1(config-if)# standby 10 track GigabitEthernet <slot/port to DCcore2>
 DCagg1(config-if)# end
 DCagg1# configure terminal
 DCagg1(config)#  interface Vlan 20
 DCagg1(config-if)# description DATA
 DCagg1(config-if)# ip address 10.130.20.1 255.255.255.0
 DCagg1(config-if)# standby 20 ip 10.130.20.254
 DCagg1(config-if)# standby 20 track GigabitEthernet <slot/port to DCcore1>
 DCagg1(config-if)# standby 20 track GigabitEthernet <slot/port to DCcore2>
@@ Line 240: / Line 216: @@
 DCagg2# configure terminal
 DCagg2(config)#  interface Vlan 10
 DCagg2(config-if)# description WLC
 DCagg2(config-if)# ip address 10.130.10.2 255.255.255.0
 DCagg2(config-if)# standby 10 ip 10.130.10.254
 DCagg2(config-if)# standby 10 track GigabitEthernet <slot/port to DCcore1>
 DCagg2(config-if)# standby 10 track GigabitEthernet <slot/port to DCcore2>
 DCagg2(config-if)# end
 DCagg2# configure terminal
 DCagg2(config)#  interface Vlan 20
 DCagg2(config-if)# description DATA
 DCagg2(config-if)# ip address 10.130.20.2 255.255.255.0
 DCagg2(config-if)# standby 20 ip 10.130.20.254
 DCagg2(config-if)# standby 20 preempt
 DCagg2(config-if)# standby 20 track GigabitEthernet <slot/port to DCcore1>
 DCagg2(config-if)# standby 20 track GigabitEthernet <slot/port to DCcore2>
+</pre>
 [[Category:CCDP]]

← Older revision		Revision as of 08:15, 12 August 2009
Line 271:		Line 271:

	DCagg2(config-if)# standby 20 track GigabitEthernet <slot/port to DCcore2>		DCagg2(config-if)# standby 20 track GigabitEthernet <slot/port to DCcore2>
		+
		+
		+	[[Category:CCDP]]

@@ Line 150: / Line 150: @@
 Fordel for globale ACL og i edge (side 90 nederst)
 <br>
 =Uddrag fra konfigurationer=

@@ Line 75: / Line 75: @@
 *BPDU guard på access porte med retning mod hosts/servere.
 *ULDL er globalt enabled,
 =Løsning=

@@ Line 60: / Line 60: @@
 *Summarize datacenter subnets i aggregation laget (retning mod DC core) med ”ip summary-address eigrp”
 *Brug ”passive-interface default” og brug ”no passive-interface”  kun på de interfaces, som er med i routing-processen
 =Default-gateway=
@@ Line 73: / Line 75: @@
 *BPDU guard på access porte med retning mod hosts/servere.
 *ULDL er globalt enabled,
 =Løsning=

@@ Line 103: / Line 103: @@
 ==Routingsprotokol==
 MANGLER
@@ Line 116: / Line 118: @@
 ===LAG3 switche===
-*10.128.0.0 / 16		DCcore1
+*10.128.0.0 / 16 - DCcore1
-*10.129.0.0 / 16		DCcore1
+*10.129.0.0 / 16 - DCcore1
-*10.130.0.0 / 16		DCagg1
+*10.130.0.0 / 16 - DCagg1
-*10.131.0.0 / 16		DCagg2
+*10.131.0.0 / 16 - DCagg2
-*10.132.0.0 / 16		CUCMswitch1
+*10.132.0.0 / 16 - CUCMswitch1
-*10.133.0.0 / 16		CUCMswitch2
+*10.133.0.0 / 16 - CUCMswitch2
 ===VLAN===
-*10.130.10.0 / 24	WLC
+*10.130.10.0 / 24 - WLC
-*10.130.20.0 / 24	DATA1
+*10.130.20.0 / 24 - DATA1
-*10.130.30.0 / 24	..
+*10.130.30.0 / 24 - ..
-*10.130.40.0 / 24	..
+*10.130.40.0 / 24 - ..
-*10.132.10.0 / 24	VOICE
+*10.132.10.0 / 24 - VOICE
 ===Point-to-point===

@@ Line 132: / Line 132: @@
 ===Point-to-point===
-*10.191.255.0 / 30   |     DCcore1 --> Campus core1
+*10.191.255.0 / 30 - DCcore1 --> Campus core1
-*10.191.255.4 / 30   |     DCcore1 --> Campus core2
+*10.191.255.4 / 30 - DCcore1 --> Campus core2
-*10.191.255.8 / 30   |     DCcore1 --> DCagg1
+*10.191.255.8 / 30 - DCcore1 --> DCagg1
-*10.191.255.12 / 30   |     DCcore1 --> DCagg2
+*10.191.255.12 / 30 - DCcore1 --> DCagg2
-*10.191.255.16 / 30   |     DCcore2 --> Campus core1
+*10.191.255.16 / 30 - DCcore2 --> Campus core1
-*10.191.255.20 / 30   |     DCcore2 --> Campus core2
+*10.191.255.20 / 30 - DCcore2 --> Campus core2
-*10.191.255.24 / 30   |     DCcore2 --> DCagg1
+*10.191.255.24 / 30 - DCcore2 --> DCagg1
-*10.191.255.28 / 30   |     DCcore2 --> DCagg2
+*10.191.255.28 / 30 - DCcore2 --> DCagg2
-*10.191.255.32 / 30   |     DCagg1 --> CUCMswitch1
+*10.191.255.32 / 30 - DCagg1 --> CUCMswitch1
-*10.191.255.36 / 30   |     DCagg2 --> CUCMswitch2
+*10.191.255.36 / 30 - DCagg2 --> CUCMswitch2

@@ Line 132: / Line 132: @@
 ===Point-to-point===
-*10.191.255.0 / 30	DCcore1 --> Campus core1
+*10.191.255.0 / 30        DCcore1 --> Campus core1
-*10.191.255.4 / 30	DCcore1 --> Campus core2
+*10.191.255.4 / 30        DCcore1 --> Campus core2
-*10.191.255.8 / 30	DCcore1 --> DCagg1
+*10.191.255.8 / 30        DCcore1 --> DCagg1
-*10.191.255.12 / 30	DCcore1 --> DCagg2
+*10.191.255.12 / 30        DCcore1 --> DCagg2
-*10.191.255.16 / 30	DCcore2 --> Campus core1
+*10.191.255.16 / 30        DCcore2 --> Campus core1
-*10.191.255.20 / 30	DCcore2 --> Campus core2
+*10.191.255.20 / 30        DCcore2 --> Campus core2
-*10.191.255.24 / 30 	DCcore2 --> DCagg1
+*10.191.255.24 / 30        DCcore2 --> DCagg1
-*10.191.255.28 / 30 	DCcore2 --> DCagg2
+*10.191.255.28 / 30        DCcore2 --> DCagg2
-*10.191.255.32 / 30	DCagg1 --> CUCMswitch1
+*10.191.255.32 / 30        DCagg1 --> CUCMswitch1
-*10.191.255.36 / 30	DCagg2 --> CUCMswitch2
+*10.191.255.36 / 30        DCagg2 --> CUCMswitch2