STM32F107VC/Interrupts and Events - Revision history

Heth: /* Example using USART2 interrupt */

2011-09-24T05:52:30Z

‎Example using USART2 interrupt

Heth: /* Example using USART2 interrupt */

2011-09-12T07:40:59Z

‎Example using USART2 interrupt

Heth: /* Example using USART2 interrupt */

2011-09-12T04:35:00Z

‎Example using USART2 interrupt

Heth at 04:34, 12 September 2011

2011-09-12T04:34:35Z

Heth: Created page with "=Nested vectored interrupt controller (NVIC)= *See the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual]..."

2011-09-12T04:34:10Z

Created page with "=Nested vectored interrupt controller (NVIC)= *See the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual]..."

New page

=Nested vectored interrupt controller (NVIC)=
*See the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual]] Chapter 10. Remember the [[STM32F107VC]] is a ''connectivity line device''.
*See the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/PROGRAMMING_MANUAL/CD00228163.pdf STM32F10xxx/20/21/L1 Cortex-M3 programming manual]] Section 4.3 for programming information. (See section 4.3.10 NVIC Design hints and Tips)
=Features=
*68 (not including the sixteen Cortex™-M3 interrupt lines)
*16 programmable priority levels (4 bits of interrupt priority are used)
*Low-latency exception and interrupt handling
*Power management control
*Implementation of System Control Registers
=Example using USART2 interrupt=
From the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual]] table 61 in section 10.1.2 its seen that
;USART2 global interrupt
:Position: '''28'''
:Priority: '''45''' - Settable
:Address: 0x0000_00D8

[[Category:STM32F107VC]][[Category:ARM]]

@@ Line 9: / Line 9: @@
 *Implementation of System Control Registers
 =Example using USART2 interrupt=
-From the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual]] table 61 in section 10.1.2 its seen that
+From the [http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual] table 61 in section 10.1.2 its seen that
 ;USART2 global interrupt
 :Position: '''28'''
 :Priority: '''45''' - Settable
 :Address: '''0x0000_00D8'''
 =Default Setup=
 The default Keil uVision [[STM32F107VC]] startup file ''startup_stm32f10x_cl.s'' contains the startup code and the Interrupt entries. Partial config below.

@@ Line 1: / Line 1: @@
 =Nested vectored interrupt controller (NVIC)=
-*See the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual]] Chapter 10. Remember the [[STM32F107VC]] is a ''connectivity line device''.
+*See the [http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf Reference manual] Chapter 10. Remember the [[STM32F107VC]] is a ''connectivity line device''.
-*See the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/PROGRAMMING_MANUAL/CD00228163.pdf STM32F10xxx/20/21/L1 Cortex-M3 programming manual]] Section 4.3 for programming information. (See section 4.3.10 NVIC Design hints and Tips)
+*See the [http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/PROGRAMMING_MANUAL/CD00228163.pdf STM32F10xxx/20/21/L1 Cortex-M3 programming manual] Section 4.3 for programming information. (See section 4.3.10 NVIC Design hints and Tips)
 =Features=
 *68 (not including the sixteen Cortex™-M3 interrupt lines)