Switch port mirroring - Revision history

Heth: /* Mirror a trunk port or other layer 2 traffic */

2025-09-03T07:46:42Z

‎Mirror a trunk port or other layer 2 traffic

2025-09-03T07:46:31Z

2018-06-21T06:34:36Z

2017-03-09T17:35:20Z

‎Dual Comm

2016-02-02T19:36:14Z

2016-01-07T09:32:11Z

‎Cisco Switch

2013-02-26T13:07:34Z

2013-02-26T13:06:52Z

‎Zyxel switch

2013-02-18T15:55:51Z

2012-03-14T07:10:09Z

‎Dual Comm

@@ Line 20: / Line 20: @@
 </source>
 == Mirror a trunk port or other layer 2 traffic==
-</source lang=cli>
+<source lang=cli>
 SW1# configure terminal
 SW1(config)# monitor session 1 source interface fastethernet0/1
 SW1(config)# monitor session 1 destination interface fastethernet 0/2  encapsulation replicate
 </source>
 =Zyxel switch=
 Copy traffic from port 1,4,5 and 6 to port 3 (Note '''both''' means mirror traffic in both directions)

@@ Line 19: / Line 19: @@
 SW1(config)# no MONITOR SESSION 1
 </source>
+== Mirror a trunk port or other layer 2 traffic==
 =Zyxel switch=
 Copy traffic from port 1,4,5 and 6 to port 3 (Note '''both''' means mirror traffic in both directions)

@@ Line 9: / Line 9: @@
 Example below: Send a copy of traffic on fastethernet 0/1 to fastethernet 0/2. Traffic in both directions are mirrored.
 <source lang=cli>
-SW1# <input>configure terminal</input>
+SW1# configure terminal
-SW1(config)# <input>monitor session 1 source interface fastethernet0/1</input>
+SW1(config)# monitor session 1 source interface fastethernet0/1
-SW1(config)# <input>monitor session 1 destination interface fastethernet 0/2</input>
+SW1(config)# monitor session 1 destination interface fastethernet 0/2
 </source>
 Remove mirror from session 1.
 <source lang=cli>
-SW1# <input>CONFIGURE TERMINAL</input>
+SW1# CONFIGURE TERMINAL
-SW1(config)# <input>no MONITOR SESSION 1</input>
+SW1(config)# no MONITOR SESSION 1
 </source>

← Older revision		Revision as of 17:35, 9 March 2017
Line 71:		Line 71:

	{{Source cli}}		{{Source cli}}
−	[[Category:Network]][[Category:Fejlfinding]]	+	[[Category:Network]][[Category:Fejlfinding]][[Category:Network management]]

← Older revision		Revision as of 19:36, 2 February 2016
Line 71:		Line 71:

	{{Source cli}}		{{Source cli}}
−	[[Category:Network]]	+	[[Category:Network]][[Category:Fejlfinding]]

@@ Line 27: / Line 27: @@
 Switch(config)# <input>interface port-channel 1,4-6</input>
 Switch(config-interface)# <input>mirror</input>
-Switch(config-interface)# <input>mirror dir egress</input>
+Switch(config-interface)# <input>mirror dir both</input>
 </source>
 Remove mirror again
@@ Line 33: / Line 33: @@
 Switch(config)# <input>no mirror-port</input>
 </source>
 =LG iPECS ES-3026P=
 ==From CLI==

@@ Line 4: / Line 4: @@
 [[Image:Switch with mirror function.png|thumb|700px|left| Switch with port mirroring]]
 |}
 =Cisco Switch=
 Example below: Send a copy of traffic on fastethernet 0/1 to fastethernet 0/2. Traffic in both directions are mirrored.

@@ Line 63: / Line 63: @@
 ==Dual Comm==
 *[http://www.lovemytool.com/blog/2010/04/review-of-dualcomm-5-port-pass-through-port-mirroring-switch-by-betty-dubois.html Artikel om Dualcomm 5-Port Pass-Through Port Mirroring Switch]
-*[http://www.dual-comm.com/gigabit_port-mirroring-LAN_switch.htm 10/100/100 Network TAP] med PoS pass-through. Powerered fra USB
+*[http://www.dual-comm.com/gigabit_port-mirroring-LAN_switch.htm 10/100/1000 Network TAP] med PoS pass-through. Powerered fra USB
 *[http://www.dual-comm.com/ Dual-Comm hjemmeside]
 {{Source cli}}
 [[Category:Network]]